Telecommunications Questions And Answers

1⟩ How to explain what is ss7?

Common Channel Signaling System No. 7 (i.e., SS7 or C7) is a global standard for telecommunications defined by the International Telecommunication Union (ITU) Telecommunication Standardization Sector (ITU-T). The standard defines the procedures and protocol by which network elements in the public switched telephone network (PSTN) exchange information over a digital signaling network to effect wireless (cellular) and wireline call setup, routing and control.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

154 views

2⟩ What is the best Rx power and Tx power at good RF Conditions?

If u r talking in the sense of Satellite then

it is 6 GHz uplink that is for transmitter and 4 Ghz for downlink frequency that is receiver frequency.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

157 views

3⟩ Buffering is? a) the process of temporarily storing the data to allow for small variation in device speeds b) a method to reduce cross talks c) storage of data within transmitting medium until the receiver is ready to receive. d) a method to reduce routing overhead.

storage of data within transmitting medium until the receiver is ready to receive.

in my opinion the following procedure buffering follws so ans is c not a.

The following procedure follows:-

1 An alarm is written into the buffer.

2The alarm is read from the buffer, sent, and re-sent until it successfully reaches the destination(receiver).

3 The alarm is removed from the buffer.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

147 views

4⟩ What is a matrix in Telecommunication?

It is a rectangular table of elements, which may be any abstract quantities that can be added an multiplied i.e m*n where m is row and n is columns.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

157 views

5⟩ The status of the Kernel is? a) task b) process c) not defined. d) none of the above.

The status of the Kernel is process

Is this answer helpful? 0 Yes | 0 No

Answer This Question

183 views

6⟩ What is the nominal voltage required in subscriber loop connected to local exchange a) +48 volts b) -48 volts c) 230 volts d) 110 volts

48 volts. This -48 volts is required by the copper wires to prevent it from corroded & eluded.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

174 views

7⟩ What is the maximal decimal number that can be accommodated in a byte? a) 128 b) 256 c) 255 d) 512

ITS 256.

SINCE, 1 BYTE=8 BITS

THE LOGIC IS 2^8=256(2 TO THE POWER OF 8)

Is this answer helpful? 0 Yes | 0 No

Answer This Question

168 views

8⟩ Max number of satellite hops allowed in voice communication is a) only one b) more han one c) two hops d) four hops

Max number of satellite hops allowed in voice communication is two hops

Is this answer helpful? 0 Yes | 0 No

Answer This Question

168 views

9⟩ Conditional results after execution of an instruction in a micro processor is stored in? a) register b) accumulator c) flag register d) flag register part of PSW(Program Status Word)

flag register part of PSW(Program Status Word)

Is this answer helpful? 0 Yes | 0 No

Answer This Question

142 views

10⟩ What action is taken when the processor under execution is interrupted by a non-maskable interrupt? a) Processor serves the interrupt request after completing the execution of the current instruction. b) Processor serves the interrupt request after completing the current task. c) Processor serves the interrupt request immediately. d) Processor serving the interrupt request depends upon the priority of the current task under execution.

Processor serves the interrupt request after completing the execution of the current instruction.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

152 views

11⟩ Purpose of PC(Program Counter) in a Microprocessor is? a) To store address of TOS(Top Of Stack) b) To store address of next instruction to be executed. c) count the number of instructions. d) to store base address of the stack.

To store address of next instruction to be executed.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

150 views

12⟩ How many T1 facilities the company needs between its office and the PSTN if it has 47 digital telephones, each operating at 64kbps 3 low-speed video machines, each operating at 384kbps 1 interactive video system, requiring 1.536 mbps.

Need 4 T1's.

Each T1 can accomodate 28 channels.

► 47 digital channels

► 3 low speed V.machines at 384 kbps.

=384/64=6channels

► 1 interactive video systemat 1.536mbps.

=153664=24 channels.

So total=47+6+24=89 channels

each T1 requires 1 synchronizing channel & 1 signalling channel.

So 4 T1 requires 8 channels.

Total=89+8=97 channels.

4T1's =112 channels-96 channels=15 channels(remains free)

Is this answer helpful? 0 Yes | 0 No

Answer This Question

143 views

13⟩ What is the need of CPG message in ISUP protocol?

Consider any call forwarding scenario.As soon as switch receives Setup, it checks that the Called_Party has forwarded option activated and so tries to forward the call. Meanwhile, Switch sends CPG message towards originator saying that Call is in Progress.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

160 views

14⟩ Line of sight is? a) Straight Line b) Parabolic c) Tx & Rx should be visible to each other d) none of the above

The line of sight is the distance or the path up to which the the TX and the RX is visible to each other because for the proper transmission there should be a ink or connectivity b/w the TX and the RX e.g. at the RF transmission the microwave links are required for the connectivity and data transmission.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

160 views

15⟩ Time taken for 1 satellite hop in voice communication is? a) 1/2 second b) 1 seconds c) 4 seconds d) 2 seconds

1/2 second

Is this answer helpful? 0 Yes | 0 No

Answer This Question

156 views

16⟩ Memory allocation of variables declared in a program is? a) allocated in RAM. b) allocated in ROM. c) allocated on stack. d) assigned to registers.

a)allocated in RAM.

stack memory is used at the time of dynamic memory allocation

ex:- malloc();

Is this answer helpful? 0 Yes | 0 No

Answer This Question

124 views

17⟩ What is TCSM ?

TRANSCODER SUBMULTIPLEXER

Is this answer helpful? 0 Yes | 0 No

Answer This Question

167 views

18⟩ A 2MB PCM(pulse code modulation) has? a) 32 channels b) 30 voice channels & 1 signaling channel. c) 31 voice channels & 1 signaling channel. d) 32 channels out of which 30 voice channels, 1 signaling channel, & 1 synchronization channel.

Answer is D.

A 2Mb PCM line has 32 channels out of which 30 voice channels, 1 signaling channel, & 1 synchronization channel(time slot 0).

Is this answer helpful? 0 Yes | 0 No

Answer This Question

145 views

19⟩ To send a data packet using datagram , connection will be established? a) before data transmission. b) connection is not established before data transmission. c) no connection is required. d) none of the above.

(c)

Is this answer helpful? 0 Yes | 0 No

Answer This Question

217 views

20⟩ Word alignment is? a) aligning the address to the next word boundary of the machine. b) aligning to an even boundary. c) aligning to a word boundary. d) none of the above.

Word alignment is aligning the address to the next word boundary of the machine.

Is this answer helpful? 0 Yes | 0 No

Answer This Question

180 views

Telecommunications

Home Information Technology (IT) Telecommunications

24 Telecommunications Questions And Answers

1⟩ How to explain what is ss7?

2⟩ What is the best Rx power and Tx power at good RF Conditions?

3⟩ Buffering is? a) the process of temporarily storing the data to allow for small variation in device speeds b) a method to reduce cross talks c) storage of data within transmitting medium until the receiver is ready to receive. d) a method to reduce routing overhead.

4⟩ What is a matrix in Telecommunication?

5⟩ The status of the Kernel is? a) task b) process c) not defined. d) none of the above.

6⟩ What is the nominal voltage required in subscriber loop connected to local exchange a) +48 volts b) -48 volts c) 230 volts d) 110 volts

7⟩ What is the maximal decimal number that can be accommodated in a byte? a) 128 b) 256 c) 255 d) 512

8⟩ Max number of satellite hops allowed in voice communication is a) only one b) more han one c) two hops d) four hops

9⟩ Conditional results after execution of an instruction in a micro processor is stored in? a) register b) accumulator c) flag register d) flag register part of PSW(Program Status Word)

11⟩ Purpose of PC(Program Counter) in a Microprocessor is? a) To store address of TOS(Top Of Stack) b) To store address of next instruction to be executed. c) count the number of instructions. d) to store base address of the stack.

12⟩ How many T1 facilities the company needs between its office and the PSTN if it has 47 digital telephones, each operating at 64kbps 3 low-speed video machines, each operating at 384kbps 1 interactive video system, requiring 1.536 mbps.

13⟩ What is the need of CPG message in ISUP protocol?

14⟩ Line of sight is? a) Straight Line b) Parabolic c) Tx & Rx should be visible to each other d) none of the above

15⟩ Time taken for 1 satellite hop in voice communication is? a) 1/2 second b) 1 seconds c) 4 seconds d) 2 seconds

16⟩ Memory allocation of variables declared in a program is? a) allocated in RAM. b) allocated in ROM. c) allocated on stack. d) assigned to registers.

17⟩ What is TCSM ?

18⟩ A 2MB PCM(pulse code modulation) has? a) 32 channels b) 30 voice channels & 1 signaling channel. c) 31 voice channels & 1 signaling channel. d) 32 channels out of which 30 voice channels, 1 signaling channel, & 1 synchronization channel.

19⟩ To send a data packet using datagram , connection will be established? a) before data transmission. b) connection is not established before data transmission. c) no connection is required. d) none of the above.

20⟩ Word alignment is? a) aligning the address to the next word boundary of the machine. b) aligning to an even boundary. c) aligning to a word boundary. d) none of the above.

Quick Links:

Telecommunications

Home Information Technology (IT) Telecommunications

24 Telecommunications Questions And Answers

1⟩ How to explain what is ss7?

2⟩ What is the best Rx power and Tx power at good RF Conditions?

3⟩ Buffering is? a) the process of temporarily storing the data to allow for small variation in device speeds b) a method to reduce cross talks c) storage of data within transmitting medium until the receiver is ready to receive. d) a method to reduce routing overhead.

4⟩ What is a matrix in Telecommunication?

5⟩ The status of the Kernel is? a) task b) process c) not defined. d) none of the above.

6⟩ What is the nominal voltage required in subscriber loop connected to local exchange a) +48 volts b) -48 volts c) 230 volts d) 110 volts

7⟩ What is the maximal decimal number that can be accommodated in a byte? a) 128 b) 256 c) 255 d) 512

8⟩ Max number of satellite hops allowed in voice communication is a) only one b) more han one c) two hops d) four hops

9⟩ Conditional results after execution of an instruction in a micro processor is stored in? a) register b) accumulator c) flag register d) flag register part of PSW(Program Status Word)

11⟩ Purpose of PC(Program Counter) in a Microprocessor is? a) To store address of TOS(Top Of Stack) b) To store address of next instruction to be executed. c) count the number of instructions. d) to store base address of the stack.

12⟩ How many T1 facilities the company needs between its office and the PSTN if it has 47 digital telephones, each operating at 64kbps 3 low-speed video machines, each operating at 384kbps 1 interactive video system, requiring 1.536 mbps.

13⟩ What is the need of CPG message in ISUP protocol?

14⟩ Line of sight is? a) Straight Line b) Parabolic c) Tx & Rx should be visible to each other d) none of the above

15⟩ Time taken for 1 satellite hop in voice communication is? a) 1/2 second b) 1 seconds c) 4 seconds d) 2 seconds

16⟩ Memory allocation of variables declared in a program is? a) allocated in RAM. b) allocated in ROM. c) allocated on stack. d) assigned to registers.

17⟩ What is TCSM ?

18⟩ A 2MB PCM(pulse code modulation) has? a) 32 channels b) 30 voice channels & 1 signaling channel. c) 31 voice channels & 1 signaling channel. d) 32 channels out of which 30 voice channels, 1 signaling channel, & 1 synchronization channel.

19⟩ To send a data packet using datagram , connection will be established? a) before data transmission. b) connection is not established before data transmission. c) no connection is required. d) none of the above.

20⟩ Word alignment is? a) aligning the address to the next word boundary of the machine. b) aligning to an even boundary. c) aligning to a word boundary. d) none of the above.

BE THE FIRST TO KNOW

Quick Links: