Safety Officer

Any task that is required to be performed at a height of 2m or more above ground level is considered as a ‘work at height’ situation.

Entry of harm full materials through mouth is called ingestion

1. The speed limits displayed along the road should be strictly

2. Short cuts and cutting across the corners should be avoid

3. No body should try to cross the level crossing when drop gates are closed

4. Signal given blocking the road ‘ stop’ look, listen and proceed should be followed.

1. Un guarded machine/ equipment

2. Poor lighting

3. Narrow road

4. Improper stacking

5. Oil on floor

6. Unsafe ventilation

7. Unsafe defective construction

8. Defective condition of tools and equipment

9. Unsafe method or procedure

10. Bad housekeeping

1. Cylinders should stored in a safe, dry and well ventilated store

2. Oxygen cylinders should be stored horizontally and acetylene cylinders shall be stored vertically.

3. The standing cylinders should be secured properly avoid falling.

4. Flammable gas shall be stored at least 50 feet away from another building

5. Oxygen cylinder shall never be stored necessary flammable gas cylinder

6. Empty cylinder shall be identified by marking with a chalk (MT) and checked for damage before returning to suppliers.

7. Cylinders should not be kept as supports.

1. All flammable material should be cleared from the work area

2. The required protective clothing and equipment must be worn

3. Cartridge respirators shall always be worn

4. Adequate ventilation is necessary

5. Adequate washing facilities must be readily available

6. Barrier cream should be applied to the skin

Attitude may be described as continuous behavior . if man’s behavior is good, then his action will be either correct or safe.

This question is designed to highlight your standards. If your “worst violation” is something your prospective employer does every day, you may be out of luck. A better idea is to give the most egregious example you can think of – something so bad that it’s highly unlikely this company is doing it on a regular basis.

☛ Good house keeping

☛ No smoking

☛ Use of fire resistant paint

☛ Electrical safety

☛ Fire check doors

☛ Noked flame safety

☛ Separate storage of hazardous chemicals

1. Not following defensive arriving techniques

2. Not observing lane displine

3. Overtaking on turns or from wrong side

4. Not obey traffic signals

5. Poor road condition

6. Poor maintained vehicle

1. Excavation area should be suitable barricade

2. Put sign boards lights and flags

3. Avoid heavy vehicle coming near the sides

4. PPE like helmet, safety shoes should be used

5. Keep the excavated soil at least 5 feet distance

6. Excavated sides should be sloped bake to a safe angle

7. Hand excavation should be done at the present of UG pipes or cables place

8. Cutting shall be done from top to bottom

9. All narrow trenches 4 feet or more deep shall be supplied at least one ladder

10. While excavating on the slope on the slope whose height is over 10 feet men should use safety belts

1. Due to wrong way using of tools.

2. Due to defective condition of tools

3. Due to failure of using right tools for right job

4. Due to wrong way of carrying tools

5. Due to strong of tools un safety

The process of joining of cutting metals by using oxygen and combustible gas is called gas cutting.

Any work above 2 meters from ground is caused work at height.

Risk assessment is conducted before an incident has occurred with the aim of avoiding any incident in the first place while incident investigation is done after an accident has occurred to determine its causes and avoid its repetition in the future.

Industrial hygiene is defined as the art and science of the presentation and improvement of the health and comfort of workers.

1. It helps to reduce the chances of fire or explosion

2. It protects the occupational diseases

3. It provides comfort to the workmen

1. A written safety policy be issued by the management’s towards men, material and machines.

2. The safety policy should bring out the management’s towards men, material machine.3

3. The safety policy should be circulated to top, middle and to workers

4. Management meeting should be in a position

5. Management should arrange for safety inspection ( once in 3 months ) and safety audit ( once in year) to be carried out.

1. Only authorized persons should used compressed air.

2. The body or clothes should not be cleaned with compressed air.

3. Compressed air hose pipes should not be placed across passage ways

4. Leakage of compressed air should not be tested with hands.

5. While working with tools run by compressed air safety shoes are to be used.

6. The tools should not be kept on position when not in use.

1. Keep fire extinguisher nearby

2. Keep fire watch near by

3. Remove all combustible from work area

4. Use all necessary PPE

5. Never put welding gas cylinder in side a confined space

6. Hoses shall not be laid in path ways

7. Gas cutting torch should have flash back arrestors

8. Gas test to be done to check for presence of flammable gas in site.

9. Good house keeping and ventilation necessary in working area.

10. Hose connections should be made properly